Lighthouse LEDs

Lighthouse LEDs Blog About LED Topics

  1. Original Xbox 360 (Phat) ROL Board Install / Removal

    What you need and what needs to have been done:   Open Xbox 360 Security Torx T8 Remove the plastics cover off of the ROL Board or (RF Board)   Then remove the three screws with the T8 screw driver.   Finally pull the board out. It is plugged in at the lower left of the board.   Lastly, plug...
  2. How to Open the Xbox 360 Controller

    What you will need for this tutorial: Security Torx T8 Driver Simply remove the screws as shown on the following spots. Don't forget the 'hidden' screw underneath the bar code behind the battery cartridge (it is shown in the picture). This one gets most people the first time. Once this is done place or hold the controller with the top facing...
  3. Xbox 360 Wired and Wireless Controller AXBY SMD LED Light Mod

    The first thing you need to do is take apart your controller so you have just the board. Please check the link below to do this if you do not already know how:How to Open The Xbox 360 ControllerOnce this is done you will need the following items:4 x 0603 SMDsWireSolderSoldering IronHot Glue GunResistors (make sure you have the correct...
  4. How to Open the Xbox 360 (Phat)

    What you need Torx screw drivers in the following sizes: T8 and T10 One small flat head screw driver or small and thin wedge (a glasses screw driver flat head, can get at a gas station or grocery store typically A pair of pliers (may or may not need them) You can also use an Xbox 360 Opening Kit if...
  5. Nintendo Wii Player Indicator LED Mod

    Opening the WiiMote (Controller)This is a very simple task. You need to look at the controller from the backside and then observe the screws. Use a Tri-Wing Screwdriver to remove all of the visible screws. There are no hidden ones that you should be worried about. Once the screws are removed simply remove the bottom part of the shell with...
  6. PS3 Controller Player Indicator LED Swap / Change Mod

    Opening the PS3 Controller This is a very simple task. You need to look at the controller from the backside and then observe the screws. Use a small phillips screwdriver to remove all of the visible screw. There are no hidden ones that you should be worried about. once the screws are removed simply remove the bottom part of the...
  7. DIP LED Polarity of 3mm, 5mm, 10mm LEDs etc...

    There are three ways to tell which side it positive or negative on an led in this fashion:Look at the long leg, that is positiveThere is usually a side or part of the led that is flat, that side is negativeIf you look inside the led you can see the larger side, which is also negative
  8. Polarity Guide of 0402, 0603, 0805, 1206 and most all smd leds

    This guide will tell you how to tell the polarity (positive/anode and negative/cathode) of leds. Most often if you can not see any of these markings, a small notch or dot will indicate the negative side of an led. This also goes for markings on a board too.
  9. Original Xbox 360 (Phat) Ring of Light LED Change - Modification

    What you will need:   20-30 Watt Soldering Iron (we, at Lighthouse LEDs, use 30 Watt) Rosin Core 60/40 .40 Solder Soldering Stand (highly recommended) Tweezers (can't do it without these) Five 0603 SMDs in your choice of color (9 if installing error lights) Xbox 360 ROL Board30 AWG Wire (optional, only if installing error lights) A pair of pliers and...
  10. Original Xbox 360 ("phat") 12v led / power source

    This is a 12v power source for leds on the Xbox 360. It can also be used for fans and other things as well. It is suggested over other sources because it takes power, almost directly, from the power brick and doesn't hardly affect any other components in the Xbox.It can be found under on the bottom side of the...

Items 11 to 20 of 23 total

Page
Lighthouse LEDs, LLC Payment Methods
© 2021 Lighthouse LEDs, LLC Store. All Rights Reserved.